Another Cool New Mustang Part! FoMoCo Stamped Stainless Steel Hose Clamp Set

We have the correct tower style Wittek hose clamps, but if you want easy to use and re-usable clamps, you may want to consider our new worm gear hose clamps. These aren't just any hose clamps either! They are the perfect "finishing touch" to your Mustang with the cool FoMoCo logo right on the top. Note: Only the small fuel line clamps do not have the FoMoCo logo.

They are not generic hose clamps. These clamps are sized properly for a clean look with no excess "tail" after tightening. Stainless steel construction means they won't rust.

Sets for small block Fords (260, 289, 302, 351W) are currently available. A set includes the following clamps:

• 2 lower radiator 2 1/8" clamps
• 2 upper radiator 2" clamps
• 6 heater hose / thermostat bypass hose 5/8" clamps
• 6 fuel line / gas sending unit 5/16"-3/8" clamps

Note: These will not fit a 6 cylinder. Kit will work on big blocks with the exception of one lower radiator hose clamp at the water pump (it is too small).

Our part number is PE-102S. Check them out by clicking here.

Install a Bigger Gas Tank in your Classic Mustang!

Install a bigger gas tank in your Classic Mustang.
www.VirginiaClassicMustang.com

If you have a '65-68 Mustang, it originally came equipped with a 16 gallon gas tank. It's super easy to increase that capacity by 6 gallons by installing a 1970 22 gallon gas tank. No modifications are needed. You just need the gas tank, a '70 Fuel Sending Unit, and one of the special filler necks listed in this post.

We have special fuel filler necks specifically bent for this conversion. Click on the links listed below:

ER-5591 65-66 Fuel Filler Steel Pipe / Neck For Use With 70 22 Gallon Gas Tank

ER-4981 67-68 Fuel Filler Steel Pipe / Neck For Use With 70 22 Gallon Gas Tank

NEW! 65-68 Mustang Fuel Sending Unit with Modern Technology

65-68 Mustang Fuel Sending Unit with modern technology
www.VirginiaClassicMustang.com

There are quite a few fuel sending units available for classic Mustangs. Because of this, it sometimes gets confusing when the time comes to purchase one.

If you have the original sending unit or your current unit hasn't been replaced in a long time, it is very likely that you may need a new one. Hopefully, you will only replace it once!

With this new gas tank sending unit, it's a very good chance that you will never have to replace it again.

There are several features that make this fuel sending unit superior to every one currently offered. In the 1980s, Ford started using new ceramic circuit board rheostats and foam floats in all of their gas tank sending units. We have brought that technology to vintage Mustangs. Surprisingly, these units are priced less than some other units currently on the market, but don't be fooled by the low price.

Here are some of the features:

• Ceramic circuit rheostat will not corrode in ethanol and is resistant to sludge build up due to old fuel in cars that are not driven often.
• Modern foam float that will never leak! Much better than the original brass float!
• Stainless steel structure that is rust resistant.
• Ethanol resistant "O" ring included.
• 3/8 inch inlet

Click here to order and read more - Part number is ER-6001.

65-68 Mustang Fuel Sending Unit with modern technology
www.VirginiaClassicMustang.com

65-68 Mustang Fuel Sending Unit with modern technology

www.VirginiaClassicMustang.com

65-68 Mustang Fuel Sending Unit with modern technology
www.VirginiaClassicMustang.com

1969, 1970 and 1971-73 Mustang Fuel Tank Sending Units

Stainless Steel Mustang Gas Tank Sending Unit.
www.VirginiaClassicMustang.com

We have had great luck with our 65-68 Stainless Steel Mustang Gas Tank Sending Units in both the 5/16" and 3/8" designs.

We now have these nice Scott Drake units available for 69, 70 and 71-73 Mustangs.  Just like the ones for the 65-68 Mustangs, these Fuel Tank Sending Units feature stainless steel construction with a brass float.

Here are the part numbers:

ER-602   69 Mustang Fuel Sending Unit

ER-603   70 Mustang Fuel Sending Unit

ER-604   71-73 Mustang Fuel Sending Unit

We also handle economy Mustang Fuel Sending Units.  Click here to see our complete line of Mustang Fuel Sending Units.

Mustang Fuel Sending Unit Brass Float

Here is another new part that just arrived.  It is the correct brass float with original style construction. Lasts longer than  plastic float.   Will fit all 65-73 Mustang Gas Tank Sending Units along with most all other Fords.  Our part number is ER-2675.

We have a complete line of Gas Tank Sending Units and Parts.  Just click here to see them all.

65-67 Mustang Fuel Sending Unit with 5/16" Inlet

We have been selling Classic Mustang parts for over 25 years now. During that time, there has never been a Gas Tank/Fuel Sending Unit available with a 5/16 inch inlet. All of the 65-early 67 Mustang originally had a 5/16 inch fuel line. The service replacement part from Ford has had a 3/8 inch inlet tube for over 30 years. It was not really a big deal, because a 5/16 inch hose could be made to work.

It is just nice that the correct one is now available. Not only does it have the correct inlet tube size, it is stainless steel construction along with the original style brass float. All units are tested by the manufacturer before being shipped.

ER601 New! 65-67 5/16" Fuel Sending Unit

ER600 67-68 3/8" Fuel Sending Unit

We also have cheaper "standard" sending units. Give us a call or check our web site.